|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
IDT74FST163209 18-BIT BUS SWITCH/ 4 PORT BUS EXCHANGER INDUSTRIAL TEMPERATURE RANGE 18-BIT BUS SWITCH/ 4 PORT BUS EXCHANGER IDT74FST163209 FEATURES: * * * * Bus switches provide zero delay paths Low switch on-resistance TTL-compatible input and output levels ESD > 2000V per MIL-STD-883, Method 3015; > 200V using machine model (C = 200pF, R = 0) * Hot insertion capability * Very low power dissipation * Available in SSOP and TSSOP packages DESCRIPTION: The FST163209 belongs to IDT's family of Bus switches. Bus switch devices perform the function of connecting or isolating two ports without providing any inherent current sink or source capability. Thus they generate little or no noise of their own while providing a low resistance path for an external driver. These devices connect input and output ports through an n-channel FET. When the gate-to-source junction of this FET is adequately forward-biased the device conducts and the resistance between input and output ports is small. Without adequate bias on the gateto-source junction of the FET, the FET is turned off, therefore with no VCC applied, the device has hot insertion capability. The low on-resistance and simplicity of the connection between input and output ports reduces the delay in this path to close to zero. The FST163209 operates as an 18-it bus switch or a 9-bit, 4 port bus exchanger. FUNCTIONAL BLOCK DIAGRAM One of Nine Channels 1A1 1B1 1A2 1B2 Flow Control S0 S1 S2 The IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE 1 (c) 2002 Integrated Device Technology, Inc. MAY 2002 DSC-3510/1 IDT74FST163209 18-BIT BUS SWITCH/ 4 PORT BUS EXCHANGER INDUSTRIAL TEMPERATURE RANGE PIN CONFIGURATION S0 1A1 1A2 ABSOLUTE MAXIMUM RATINGS(1) Symbol VTERM(2) Description Terminal Voltage with Respect to GND Storage Temperature Maximum Continuous Channel Current Max -0.5 to +7 -65 to +150 128 Unit V C mA 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 S1 S2 1B1 1B2 2B1 2B2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 TSTG IOUT GND 2A1 2A2 NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. Vcc, Control, and Switch terminals. VCC 3A1 3A2 GND 3B1 3B2 CAPACITANCE(1) Symbol CIN CI/O Parameter Control Input Capacitance Switch Input/Output Capacitance Switch Off Conditions(2) Typ. 6 17 Unit pF pF GND 4A1 4A2 5A1 5A2 GND 4B1 4B2 5B1 5B2 NOTES: 1. Capacitance is characterized but not tested. 2. TA = 25C, f = 1MHz, VIN = 0V, VOUT = 0V. GND 6A1 6A2 7A1 7A2 GND 6B1 6B2 7B1 7B2 PIN DESCRIPTION Pin Names A1, A2 B1, B2 S0-2 I/O I/O I Description Buses A1, A2, B1, B2 Control pins for MUX and Switch Enable Functions GND 8A1 8A2 9A1 9A2 GND 8B1 8B2 9B1 9B2 FUNCTION TABLE(1) S2 L L L L H H H H S2 L L H H L L H H S0 L H L H L H L H A1 Z B1 B2 Z Z Z B1 B2 A2 Z Z Z B1 B2 Z B2 B1 Function Disconnect A1 to B1 A1 to B2 A2 to B1 A2 to B2 Disconnect A1 to B1, A2 to B2 A1 to B2, A2 to B1 SSOP/ TSSOP TOP VIEW NOTE: 1. H = HIGH Voltage Level L = LOW Voltage Level Z = High-Impedance 2 IDT74FST163209 18-BIT BUS SWITCH/ 4 PORT BUS EXCHANGER INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Industrial: TA = -40C to +85C, VCC = 5.0V 10% Symbol VIH VIL IIH IIL IOZH IOZL VIK IOFF ICC Parameter Control Input HIGH Voltage Control Input LOW Voltage Control Input HIGH Current Control Input LOW Current Current During Bus Switch Disconnect Clamp Diode Voltage Switch Power Off Leakage Quiescent Power Supply Current VCC = Min., IIN = -18mA VCC = 0V, VIN or VO 5.5V VCC = Max., VIN = GND or VCC VCC = Max., VO = 0 to 5V Test Conditions(1) Guaranteed Logic HIGH for Control Inputs Guaranteed Logic LOW for Control Inputs VCC = Max. VI = VCC VI = GND Min. 2 -- -- -- -- -- -- -- -- Typ.(2) -- -- -- -- -- -- -0.7 -- 0.1 Max. -- 0.8 1 1 1 1 -1.2 1 3 V A A A Unit V V A BUS SWITCH IMPEDANCE OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Industrial: TA = -40C to +85C, VCC = 5.0V 10% Symbol RON IOS Parameter Switch On Resistance Short Circuit Current (2) Test Conditions Vcc = Min., VIN = 0V, ION = 64mA Vcc = Min., VIN = 0V, ION = 30mA Vcc = Min., VIN = 2.4V, ION = 15mA Vcc = Max., VO = GND Min. -- -- -- -- Typ. 4 4 6 (1) Max. 7 7 15 -- Unit mA (3) 300 NOTES: 1. Typical values are at Vcc = 5.0V, +25C ambient. 2. The voltage drop between the indicated ports divided by the current through the switch. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 3 IDT74FST163209 18-BIT BUS SWITCH/ 4 PORT BUS EXCHANGER INDUSTRIAL TEMPERATURE RANGE POWER SUPPLY CHARACTERISTICS Symbol ICC ICCD Parameter Quiescent Power Supply Current TTL Inputs HIGH Dynamic Power Supply Current(4) VCC = Max. VIN = 3.4V(3) VCC = Max. Outputs Open Select Input Togging 50% Duty Cycle VCC = Max. Outputs Open Three Select Pins Toggling (Nine Switches Toggling) fi = 10MHz 50% Duty Cycle NOTES: 1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type. TA = -40C to +85C 2. Typical values are at VCC = 5.0V, +25C ambient. 3. Per TTL driven input (VIN = 3.4V). All other inputs at VCC or GND. Switch inputs do not contribute to ICC. 4. This parameter represents the current required to switch the internal capacitance of the control inputs at the specified frequency. Switch inputs generate no significant power supply currents as they transition. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations. 5. CPD = ICCD/VCC CPD = Power Dissipation Capacitance 6. IC = IQUIESCENT + IINPUTS + IDYNAMIC IC = ICC + ICC DHNT + ICCD (fiN) ICC = Quiescent Current ICC = Power Supply Current for a TTL High Input (VIN = 3.4V) DH = Duty Cycle for TTL Inputs High NT = Number of TTL Inputs at DH ICCD = Dynamic Current Caused by an Input Transition Pair (HLH or LHL) fi = Control Input Frequency N = Number of Control Inputs Toggling at fi Test Conditions(1) Min. -- Typ.(2) 0.5 120 Max. 1.5 160 Unit mA A/ MHz/ Select mA VIN = VCC VIN = GND -- IC Total Power Supply Current(6) VIN = VCC VIN = GND VIN = 3.4V VIN = GND -- 3.6 4.8 -- 4.4 7.1 SWITCHING CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Industrial: TA = -40C to +85C, VCC = 5.0V 10% Symbol tPLH tPHL tBX tPZH tPZL tPHZ tPLZ |QCI| |QDCI| Description(1) Data Propagation Delay A to B, B to A(2) Switch Multiplex Delay S to A, B Switch CONNECT Delay S to A, B Switch DISCONNECT Delay S to A, B Charge Injection During Switch DISCONNECT, Sx to xAx or xBx(3) Charge Injection During Switch Multiplex, Sx to xAx or xBx(3) VCC = 5V 10% Min. -- 1.5 1.5 1.5 -- -- Typ. -- -- -- -- 1.5 0.5 Max. 0.25 6.5 6.5 7 -- -- VCC = 4V Max. 0.25 7 7 7 -- -- Unit ns ns ns ns pC NOTES: 1. See test circuits and waveforms. 2. The bus switch contributes no Propagation Delay other than the RC Delay of the load interacting with the RC of the switch. 3. |QCI| is the charge injection for a single switch DISCONNECT and applies to either single switches or multiplexers. |QDCI| is the charge injection for a multiplexer as the multiplexed port switches from one path to another. Charge injection is reduced because the injection from the DISCONNECT of the first path is compensated by the CONNECT of the second path. 4 IDT74FST163209 18-BIT BUS SWITCH/ 4 PORT BUS EXCHANGER INDUSTRIAL TEMPERATURE RANGE TEST CIRCUITS AND WAVEFORMS V CC 500 VIN Pulse Generator RT D.U.T . VOUT OUTPUT tPLH 50pF CL 500 OPPOSITE PHASE INPUT TRANSITION tPHL 7.0V SAME PHASE INPUT TRANSITION tPLH tPHL 3V 1.5V 0V VOH 1.5V VOL 3V 1.5V 0V Propagation Delay Test Circuits for All Outputs 3V 1.5V 0V 3V 1.5V 0V 3V 1.5V 0V 3V 1.5V 0V SWITCH POSITION Test Open Drain Disable Low Enable Low All Other Tests Switch Closed Open DATA INPUT TIMING INPUT ASYNCHRONOUS CONTROL SYNCHRONOUS CONTROL tSU tH tREM DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. tSU tH Set-up, Hold, and Release Times VCC ENABLE 1 MHz Signal Generator Enable/Select Switch In Switch In (MUX) (2) (1) DISABLE 3V 1.5V Switch D.U.T Out . VOUT (3) CONTROL INPUT CL = 50pF tPZL OUTPUT NORMALLY LOW OUTPUT NORMALLY HIGH SWITCH CLOSED tPZH 3.5V 1.5V tPHZ 0.3V 1.5V 0V tPLZ 0V 3.5V 0.3V VOL VOH 0V Charge Injection NOTES: 1. Select is used with multiplexers for measuring IQDCII during multiplexer select. During all other tests Enable is used. 2. Used with multiplexers to measure IQDCII only. 3. Charge Injection = VOUT CL, with Enable toggling for IQCII or Select toggling for IQDCII. VOUT is the change in VOUT and is measured with a 10M probe. SWITCH OPEN Enable and Disable Times NOTES: 1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH. 2. Pulse Generator for All Pulses: Rate 1.0MHz; tF 2.5ns; tR 2.5ns. LOW-HIGH-LOW PULSE tW HIGH-LOW-HIGH PULSE 1.5V 1.5V Pulse Width 5 IDT74FST163209 18-BIT BUS SWITCH/ 4 PORT BUS EXCHANGER INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION IDT XX FST Temp. Range XXX Family XXX Device Type X Package PV PA Shrink Small Outline Package Thin Shrink Small Outline Package 209 163 74 18-Bit Bus Switch/4 Port Bus Exchanger Double-Density Bus Switch -40C to +85C DATA SHEET DOCUMENT HISTORY 5/21/2002 Removed TVSOP package CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com for Tech Support: logichelp@idt.com (408) 654-6459 6 |
Price & Availability of IDT74FST163209 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |